What we fix · Brookline, MA
Wolf Cooktop Repair
Wolf gas, induction and electric cooktops set into island and peninsula counters. Burner and spark assemblies, induction coils and generators, touch and knob controls, and glass and trim hardware.
Flat $95 service call — the trip and the full diagnosis — credited against the repair if you approve one.
The call
How it gets described
- Induction zone dropping out under a heavy pan
- Sealed burner that lights then dies at low flame
- A chip or crack in the glass around a zone
- Control knob spinning without changing the flame
The visit
What gets measured
- Inverter temperature and cooling airflow under a loaded pan
- Spark electrode gap and the condition of its porcelain
- Burner port pattern and flame colour at full and at simmer
- Touch control response and relay behaviour on electric zones
Cost
Quoted in full before anything comes apart
Flat $95 service call covering the visit and full diagnosis, credited against the repair once you approve it. These are the bands most repairs land in once the fault is known.
- $270$690 Igniter or spark module replacement
- $260$1,090 Burner valve or orifice service
- $140$720 Oven thermostat or sensor calibration
- $320$870 Convection fan or motor
- $540$1,550 Control board or touch panel
- $200$970 Door hinge, glass or seal
Repair or replace? A comparable new unit is $6,900 to $19,530
A comparable pro range, appliance only — before delivery, installation, gas or electrical work and any cabinetry. A rangetop plus separate wall ovens lands differently again.
What moves a job inside its band
Which part failed
An igniter and a control board are the two ends of the same appliance. Ignition, sensors and hardware sit at one end of the range; boards, gas valves and blower assemblies sit at the other.
Whether it is a current part
A part for a platform still in production arrives quickly. A superseded board or a discontinued blower means a supersession lookup and a wait, and the quote says so.
What it takes to get at it
A range that pulls forward on a tile floor is a different job from a slide-in trapped by a stone counter, or a hood liner four metres up a shared riser.
One visit or two
If the part is on the van it finishes that day. If it has to be ordered, the return visit is inside the quoted figure rather than added to it.
Questions
Cooktop Repair: two questions before you call
There is a chip in the glass around one zone. Can it still be used?
Not safely, and not for long. A chip becomes a crack under thermal cycling, and once it reaches the coil or the element beneath it you have an electrical problem as well as a glass one. Stop using that zone and let us look at what replacement actually involves on your model.
A sealed burner lights and then dies at the low setting.
That is the simmer adjustment or the port ring, not the igniter. Every burner has a low-flame screw set at the factory that can drift after a deep clean or a regulator change, and a partly blocked ring will hold a full flame but not a small one.
Reviews
After a cooktop repair visit
4.9 / 5
from 974 reviews
5 out of 5
A hairline crack appeared near the front right zone and I assumed the unit was scrap. He replaced the glass and trim on their own and kept the frame and controls. The part took a fortnight to reach us.
Lucian E.Putterham
5 out of 5
The induction zone kept dropping out under a heavy stock pot mid boil. A cooling fan below the glass had clogged with dust and the generator was overheating. Cleaned, new fan, and it has run steadily since.
Clodagh F.Longwood
5 out of 5
Touch controls went dead after a spill ran under the trim. He dried and reseated the ribbon, found one board corroded, and fitted a replacement. He also showed me how to lock the panel before wiping it down.
Marguerite Y.Coolidge Corner
Book it
Get it cooking again
Cooktop Repair in Brookline — the model number and the symptom is enough to start.
(781) 410-4833Flat $95 service call, credited against an approved repair.
